STANDARD NUTS—COARSE AND FINE THREAD

STANDARD NUTS—COARSE AND FINE THREAD

HEAVY HEX NUTS

Compared to Hex Nuts, the Heavy Hex series is wider by 1/8″ across flats. This
provides a number of advantages. Heavy Hex Nuts can span eccentric or oversize bolt holes. They offer increased bearing area to support higher bearing stresses;and they have thicker walls to control nut dilation under load. These effects are most pronounced in the smaller sizes. RB&W stocks four grades of Heavy Nuts to meet various customer specification requirements. All are made in coarse thread only.

ASTM A307 grade for general applications is available in sizes from 1/4-inch through 4 inches.

ASTM A194 Grade 2 and 2H provide medium carbon steel product for high pressure and high temperature applications. Available in sizes 5/8 through 1-inch in coarse thread series. In sizes larger than 1-inch, both grades are stocked in 8-pitch series. Sizes 1-1/8 and
1-1/4-inch are also stocked in 7-pitch series for use with A325 and A490 bolts in tructural applications.
Identification: a 2 or 2H on the top face.

A325 Grade for use with High Strength Bolts to ASTM

A325 specification. Identification: three circumferential
dashes on the nut faces.

HEX SLOTTED NUTS

Made with dimensions identical
to Hex Full Nuts. Six radial slots on the top permit
proper alignment with a drilled hole in the end of a
bolt to accommodate a cotter pin or safety wire for
position locking.
Sizes 1/4 to 1-1/2 inches, in both fine and coarse
threads.

HEX MACHINE SCREW NUTS

These nuts are made
by blanking from low carbon strip or sheet steel.
They are normally available double chamfered and
double countersunk to permit assembly from either
side. Such nuts are used on small, light assemblies
where substantial strength and clamping force are
rarely involved.
Available in various finishes, such as zinc or cadmium
plate; or with phosphate coatings. Stocked in sizes
No. 5 through 3/8 inch.

HEX HIGH NUTS

Dimensions across flats are the
same as those for Hex Nuts. Height dimension is
approximately one-third larger than the Hex Thick
Nut. High Nuts may be hardened and utilized for
severe applications such as tractor pad bolts and
spring shackle bolts.
Stocked in sizes 3/8 to 1-1/4 inches, in fine thread
only.

HEX THICK NUTS–HEX THICK SLOTTED NUTS

Dimensions across flats are the same as those for
Hex Nuts, but they’re thicker in the height dimension.
Purpose of this design is to provide additional thread
engagement for severe fastening applications—such
as those that require Grade 8 bolts.
They are also produced slotted for use with cotter
pins. Hex Thick Nuts are stocked in sizes 1/4 to 1-1/2
inches, fine thread only. Hex Thick Slotted Nuts are
stocked in sizes 1/4 to 1-inch, fine thread only.

HEAVY SLOTTED NUTS

Similar to the Hex Slotted series, but wider by 1/8-inch across flats. Six slots milled into top of nut permit position locking with cotter pin or wire through drilled hole in bolt.
Stocked in sizes 1/4 to 2 inches, in coarse thread
only.

HEX CASTLE NUTS

Like the slotted nut design,
castle nuts have six radial slots to permit use of cotter
pins or safety wire for locking into position. The
chief difference is in the top of the nut. The castle nut
permits the cotter pin or wire to be wrapped around
its crown.
Stocked in sizes 1/4 to 1-1/2 inches, in fine thread
only.

SQUARE NUTs—This shape of nut is declining in
use, being replaced by the more convenient, easierto-
wrench, hex shaped product in almost all applications.
Square nuts are sometimes specified for
square head bolts. They have a chamfered top and
flat face. The long dimension across corners enables
them to span oversize bolt holes, and to withstand
severe wrenching stresses.
Stocked in sizes 1/4 to 1 inch. Available in coarse
thread only.

HEAVY SQUARE NUTS—This series of nuts provides
additional width and height where desirable, as in the
case of bolts being used for non-critical assembly of
steelwork. Heavy Square Nuts have a flat face and a
chamfered flat or washer crowned top.
Stocked in sizes 1/4 to 1 inch, in coarse thread only.

Please follow and like us:

Leave a Reply